• IAIP

    Hover for detail

    IAIP

    Injection Controller

    The IAI Additive Injection Controller is a universally powered (85-265VAC) or 10-40VDC powered injection controller for liquids featuring a 2.8 inch TFT colour LCD display at 320x480 pixels, a M3 32 bit ARM processor and quadrature pulse input for main and additive flow. The IAI Controller combines with an additive injection manifold to provide a compact additive injection system. The system is configured by push buttons on a four-button infrared remote control or RS485 communication from a host.



    • Simple touch switch set up with English statement prompts by approved IR remote
    • Low cost - High performance
    • Programmable dual channel quadrature input or single pulse train with DIP switch selection for turbine, reed switch & open collector
    • Background total for main flow and additive flow
    • Dual 4-20mA output with Proportional and Integral algorithm control from the main and additive flow signal for modulating valve control for continuous dispensing of additive
    • Main flow and additive flow rate display
    • Sensor supply that can be adjusted from 8 to 20VDC
    • Micro SD card for 8GB for storage of batching data
    • 85 to 265VAC 47-63 Hz universal supply or factory fitted 10 to 40VDC isolated supply

    The controller can operate in:
    Pace Mode
    Injection rate on the main flow throughput and a user programmed algorithm
    Permissive Pace Mode
    Injection rate on the main flow throughput, a user programmed algorithm and enabled by a permissive input
    Slave Mode
    Inject additive enabled by the squirt button or remotely wired to the permissive input
    Control Mode
    Start injection from first received main flow pulse and IAI algorithm, and stop at programmed batch size
    Remote mode
    Algorithm and start signal from communication link

    Input Details

    The IAI accepts a dual channel input from 0 to 2KHZ and is DIP switch selectable for open collector, reed, Hall and turbine signals (from 20mV peak to peak)

    Standard features
    • External squirt button included on EXD housing
    • Injector block size 4 [.01 to 1.0 LPM] selection size by application
    • Injector block size 6 [.03 to 1.66 LPM] selection size by application
    • Injector block size 8 [.25 to 10.0 LPM] selection size by application
    • Controller accuracy +/- 0.5% with a repeatability of +/- 0.25%
    Display

    The IAI incorporates a 64x128 dot graphics module with RGB backlight in English

    Infrared Remote

    Four button IR remote is potted in epoxy and complies with AS/NZS 60079.18: 2005

    Environmental Parameters
    • -20 to 50°C
    • Humidity 5-95%
    • Protection class to IP66
    • Approvals IECEX (enclosure)
    Electrical Parameters
    • 4 of voltage free inputs 24VDC tolerant
    • 6 of open collector outputs 24VDC tolerant @ 200mAmpere
    • 1 of timed open collector output 24VDC tolerant @ 200mAmpere
    • 4 of relay outputs 240VAC tolerant SSR @ 2Ampere with external snubber or
    • 4 of relay outputs 240VAC tolerant mechanical@ 2Ampere with external snubber
    • Communications: Isolated 2 wire RS485 with Modbus RTU protocol
    Power Supply

    85 to 265VAC 47-63 Hz or DC to DC converter isolator from 10 to 40VDC. An adjustable transducer power supply of 8 to 20VDC at 30mA is incorporated.

    Mounting Details
    • Surface mounting IP66 plastic enclosure of case dimensions 200mm wide x 200mm high x 95mm deep with fixing centres of 182mm wide x182mm high by M4 screws.
    • 6 of M20 cable entries available for user connection
    • Weight is 2kg
    Ordering Information
    • Model Structure: model/input/display/power supply/options
    • Sample Number: IAIP/2xB/0-99999999/VAC